Driver Disk for QLogic fastlinq 8.33.9.0 – For XenServer 7.1

Who Should Install this Driver Disk?

Customers running Citrix XenServer 7.1.0 who use Qlogic’s fastlinq driver and wish to use the latest version of the following:

Driver Module Version
fastlinq 8.33.9.0

Issues Resolved In this Driver Disk

Includes general enhancements and bug fixes.

Note: If your device has been branded by your OEM, please ensure that you consult them regarding the currently supported driver/firmware versions.

Installing the Driver Disk

Customers should use XenServer Command Line Interface (CLI) to install this update. Once the driver has been installed, the server must be restarted. As with any software update, Citrix advises customers to back up their data before applying this driver disk.

Please note that the attachment to this article is a zip file. It contains both the driver disk ISO mentioned below, and the source code for the driver. The zip file should be unzipped (to produce the driver disk ISO image), before carrying out the steps below. The source code ISO is not necessary for driver disk installation: it is provided to fulfill licensing obligations.

Installing as Part of a Clean XenServer Installation

  1. Once you have selected your keyboard layout at the first installer prompt, you will be presented with a welcome screen. At this point, press F9 on your keyboard, and insert the CD with the driver disk in it, or use one of the other methods such as installation over the network.

    Users should note that if installation over HTTP or FTP is to be used, the ISO image must be unpacked at that location (i.e. the installer expects to find the contents of the ISO at that network location, not the ISO itself).

  2. The installer will proceed to attempt to load the driver. If this is successful, you can continue with the installation as normal. Near the end of the installation, you will be prompted to re-insert the driver disk (otherwise known as a XenServer supplemental pack) so that the driver can be installed onto disk. You must re-supply the driver disk at this point. Failure to do so will mean that the installation will not contain the new drivers. After this step, no further action is required.

If the installer fails to load the new driver from the driver disk, it is likely to be because an earlier version of the driver has already been loaded. In general, this is because a hardware component is present that is supported by the version of the driver that ships as part of XenServer (even if another component is present that requires a newer version of the driver). To avoid the existing driver being loaded, use the following procedure.

  1. Reboot the host, leaving the XenServer installation CD-ROM in the drive.
  2. At the boot: prompt, type:

    shell

  3. You will now be presented with a command prompt. Type the following:

    rmmod fastlinq

    rmmod qed

    If these commands succeed (i.e. there are no error messages printed), the installer’s versions of the drivers have been unloaded. If error messages are presented, it is likely that other drivers depend on one or more of the drivers you are attempting to unload. If this is the case, please contact Citrix Technical Support.

  4. Type

    exit

    or press Control+D on your keyboard, to return to the installer.

  5. Use the procedure described above to provide the driver disk to the installer, which should now load correctly.

Installing the Update by using the xe Command Line Interface

Perform the following steps to install the update remotely using the xe CLI:

  1. Download the update to a known location on a computer that has XenCenter installed.
  2. Upload the update:

    xe update-upload file-name=driver-qlogic-fastlinq-8.33.9.0.iso

    Note: The UUID of the update is returned when the upload completes.

  3. Apply the update:

    xe update-apply uuid=8ed47114-17f9-463c-9f65-0f6f0c0f3663

  4. To complete the installation, restart the host. This ensures that the driver loads correctly.

Files

Update Files

Component Details
Filename driver-qlogic-fastlinq-8.33.9.0.iso
File sha256 63cc4433296a53bdae41bef4efb6ddcbd2793871ed16d1aa9890010e0b64a56f
Source Filename driver-qlogic-fastlinq-8.33.9.0-sources.iso
Source File sha256 4ea9598890bc0f679c5792c03990f19f5ed529bcf3dd6137acff712ac61e4ad2
Zip Filename driver-qlogic-fastlinq-8.33.9.0.zip
Zip File sha256 1e49d596796de8be9cda2d4a2d98ccab94677ce18781921d9c33c344b8f40a92
Size of the Zip file 141.37 MB

RPMs Provided

RPM Name
qlogic-fastlinq-8.33.9.0-5.x86_64.rpm

More Information

If you experience any difficulties, contact Citrix Technical Support.

For information on how to build driver disks, refer to Citrix XenServer ® 7.1 Supplemental Packs and the DDK Guide.

Related:

Leave a Reply