Driver Disk for Microsemi smartpqi 1.1.4-132 – For XenServer 7.1

Who Should Install this Driver Disk?

Customers running a Citrix XenServer 7.1 LTSR who use Microsemi’s smartpqi driver and wish to use the latest version of the following:

Driver Module Version
smartpqi 1.1.4-132

Issues Resolved In this Driver Disk

Includes general enhancements and bug fixes.

Firmware requirements for this Driver Disk

Please ensure that your hardware is running firmware versions greater or equal to the ones specified below, according to the chipset of your particular device:

  • Microsemi Adaptec SmartHBA 2100 Adapters with Firmware 1.60 [0]
  • Microsemi Adaptec SmartRAID 3100 Adapters with Firmware 1.60 [0]

Note: If your device has been branded by your OEM, please ensure that you consult them regarding the currently supported driver/firmware versions.

Installing the Driver Disk

Customers should use XenServer Command Line Interface (CLI) to install this update. Once the driver has been installed, the server must be restarted. As with any software update, Citrix advises customers to back up their data before applying this driver disk.

Please note that the attachment to this article is a zip file. It contains both the driver disk ISO mentioned below, and the source code for the driver. The zip file should be unzipped (to produce the driver disk ISO image), before carrying out the steps below. The source code file is not necessary for driver disk installation: it is provided to fulfill licensing obligations.

Installing as Part of a Clean XenServer Installation

  1. After you have selected your keyboard layout at the first installer prompt, you will be presented with a welcome screen. At this point, press F9 on your keyboard, and insert the CD with the driver disk in it, or use one of the other methods such as installation over the network.

    Note: If installation over HTTP or FTP is to be used, the ISO image must be unpacked at that location (i.e. the installer expects to find the contents of the ISO at that network location, not the ISO itself).

  2. The installer will proceed to attempt to load the driver. If this is successful, you can continue with the installation as normal. Near the end of the installation, you will be prompted to re-insert the driver disk (otherwise known as a XenServer supplemental pack) so that the driver can be installed onto disk. You must re-supply the driver disk at this point. Failure to do so will mean that the installation will not contain the new drivers. After this step, no further action is required.

If the installer fails to load the new driver from the driver disk, it is likely to be because an earlier version of the driver has already been loaded. In general, this is because a hardware component is present that is supported by the version of the driver that ships as part of XenServer (even if another component is present that requires a newer version of the driver). To avoid the existing driver being loaded, use the following procedure.

  1. Reboot the host, leaving the XenServer installation CD-ROM in the drive.
  2. At the boot: prompt, type:


  3. You will now be presented with a command prompt. Type the following:

    rmmod smartpqi

    If this succeeds (i.e. there are no error messages printed), the installer’s versions of the drivers have been unloaded. If error messages are presented, it is likely that other drivers depend on one or more of the drivers you are attempting to unload. If this is the case, please contact Citrix Technical Support.

  4. Type


    or press Control+D on your keyboard, to return to the installer.

  5. Use the procedure described above to provide the driver disk to the installer, which should now load correctly.

Installing the Update by using the xe Command Line Interface

Perform the following steps to install the update remotely using the xe CLI:

  1. Download the update to a known location on a computer that has XenCenter installed.
  2. Upload the update:

    xe update-upload file-name=driver-microsemi-smartpqi-1.1.4_132.iso

    Note: The UUID of the update is returned when the upload completes.

  3. Apply the update:

    xe update-apply uuid=043e662c-d5a3-4d65-8ede-6df19e7f8554

  4. To complete the installation, restart the host. This ensures that the driver loads correctly.


Update Files

Component Details
Filename driver-microsemi-smartpqi-1.1.4_132.iso
File sha256 6b041541144d6b0605f6973495bea29511dc6f52aec86bc03a432cf06773a02f
Source Filename driver-microsemi-smartpqi-1.1.4_132-sources.iso
Source File sha256 44acad5ed431a3bfaf938daf808a59c3156a9ca34c1b44da59818784026b0e91
Zip Filename
Zip File sha256 a73a39847ec87c58ebec877b853ab1cfe1de0ec9064b8d4b6b1c1a93f8463967
Size of the Zip file 135.16 MB

RPMs Provided

RPM Name

More Information

If you experience any difficulties, contact Citrix Technical Support.

For information on how to build driver disks, refer to Citrix XenServer Supplemental Packs and the DDK Guide .


Leave a Reply