Driver Disk for Qlogic qla2xxx 10.02.04.00-k – For Citrix Hypervisor 8.2 LTSR

Who Should Install this Driver Disk?

Customers on non-Dell hardware running the Citrix Hypervisor 8.2 LTSR release who use Qlogic’s qla2xxx driver and wish to use the latest version of the driver.

Note: If you use Dell hardware, do not install this driver disk. This versions of the driver disk is not supported on Dell hardware. Instead, install version 10.02.03.00-k

Driver Module Version
qla2xxx 10.02.04.00-k

Issues Resolved In this Driver Disk

Includes general enhancements and bug fixes.

Installing the Driver Disk

Customers should use the Citrix Hypervisor CLI to install this update. Once the driver has been installed, the server must be restarted. As with any software update, Citrix advises customers to back up their data before applying this driver disk.

Please note that the attachment to this article is a zip file. It contains both the driver disk ISO mentioned below, and the source code for the driver. The zip file should be unzipped (to produce the driver disk ISO image), before carrying out the steps below. The source code file is not necessary for driver disk installation: it is provided to fulfill licensing obligations.

Installing as Part of a Clean Citrix Hypervisor Installation

  1. After you have selected your keyboard layout at the first installer prompt, you will be presented with a welcome screen. At this point, press F9 on your keyboard, and insert the CD with the driver disk in it, or use one of the other methods such as installation over the network.

    Note: If installation over HTTP or FTP is to be used, the ISO image must be unpacked at that location (i.e. the installer expects to find the contents of the ISO at that network location, not the ISO itself).

  2. The installer will proceed to attempt to load the driver. If this is successful, you can continue with the installation as normal. Near the end of the installation, you will be prompted to re-insert the driver disk (otherwise known as a Citrix Hypervisor supplemental pack) so that the driver can be installed onto disk. You must re-supply the driver disk at this point. Failure to do so will mean that the installation will not contain the new drivers. After this step, no further action is required.

If the installer fails to load the new driver from the driver disk, it is likely to be because an earlier version of the driver has already been loaded. In general, this is because a hardware component is present that is supported by the version of the driver that ships as part of XenServer (even if another component is present that requires a newer version of the driver). To avoid the existing driver being loaded, use the following procedure.

  1. Reboot the host, leaving the Citrix Hypervisor installation CD-ROM in the drive.
  2. At the boot: prompt, type:

    shell

  3. You will now be presented with a command prompt. Type the following:

    rmmod qla2xxx

    If this succeeds (i.e. there are no error messages printed), the installer’s versions of the drivers have been unloaded. If error messages are presented, it is likely that other drivers depend on one or more of the drivers you are attempting to unload. If this is the case, please contact Citrix Technical Support.

  4. Type

    exit

    or press Control+D on your keyboard, to return to the installer.

  5. Use the procedure described above to provide the driver disk to the installer, which should now load correctly.

Installing the update by using the xe CLI

Perform the following steps to install the update remotely using the xe CLI:

  1. Download the update to a known location on a computer that has XenCenter installed.
  2. Upload the update:

    xe update-upload file-name=driver-qlogic-qla2xxx-10.02.04.00_k.iso

    Note: The UUID of the update is returned when the upload completes.

  3. Apply the update:

    xe update-apply uuid=c37bacd1-4624-49ac-9b22-d35f7e83cf67

  4. To complete the installation, restart the host. This ensures that the driver loads correctly.

Files

Update Files

Component Details
Filename driver-qlogic-qla2xxx-10.02.04.00_k.iso
File sha256 355011027651c914162f2801c8a13977461a14479c04fd73adcba409b44567c8
Source Filename driver-qlogic-qla2xxx-10.02.04.00_k-sources.iso
Source File sha256 b3af3d5fde7643c0df0948f73b4ca193964bd83c4e166286d60b81f695a60f68
Zip Filename driver-qlogic-qla2xxx-10.02.04.00_k.zip
Zip File sha256 998831c7128d85574173276c3c89b8bce3de32ddb03858c5cede8f93c293ab05
Size of the Zip file 162.12 MB

RPMs Provided

RPM Name
qlogic-qla2xxx-10.02.04.00_k-1.el7.centos.x86_64.rpm

More Information

For a list of the driver versions and the latest driver disk updates available, see Driver versions for XenServer and Citrix Hypervisor.

If you experience any difficulties, contact Citrix Technical Support.

For information on how to build driver disks, refer to Citrix Hypervisor Supplemental Packs and the DDK Guide .

Related:

  • No Related Posts

Leave a Reply